固体碳直接还原钢铁厂含锌固废的理论与实践

 钢铁厂内的含锌固废数量巨大，同时富含铁、碳等元素，是可循环再利用的二次资源。通过固体碳直接还原ZnO和FeO的热力学分析，发现在非标准状态下，ZnO的还原条件要优于FeO。为此，在实验室条件下设计了含锌固废在不同温度和时间下的还原试验，发现在还原温度为1 423 K、还原时间为15 min以上时，脱锌率可达到90%，而铁的金属化率需要在1 573 K时才能接近90%；在还原温度低于1 423 K时，还原时间对脱锌率的影响较大；在还原温度高于1 473 K时，还原温度对脱锌率影响较小，同时脱锌率可达到95%。这些结果对国内当前处理含锌固废主要工艺(回转窑、转底炉)的操作制度设置具有重要的参考价值，也为如何选择合理的工艺路线，以低投入、低运营成本实现含锌固废的再利用提供了理论依据。     

Evolution of properties of parts during MIM and sintering of recycled oxide particles

Metal injection moulding (MIM) is an established process for high volume production of complex shaped metallic parts using commercially available feedstocks. The characteristics of parts after moulding, debinding, and sintering cannot be simply predictable from raw materials because the properties get altered with the process parameters and the corresponding levels of porosity during processing steps. In this study, physical properties, microstructure, and mechanical properties of the MIM parts have been characterised to understand the evolution of strength during various steps in MIM processing. Feedstocks with different binder loading show a considerable difference in physical as well as mechanical characteristics. During sintering of parts which have solid loading of grinding sludge, simultaneous in situ reduction and densification takes place, whereas only densification occurs in carbonyl iron parts. It is, therefore, possible to make complex shaped parts of different levels of porosity from downgraded shop floor metallic waste.     

Experimental study on flame spread along fuel cylinders in high pressures

Flame spread over solid fuels in high‐pressure situations, such as nuclear containment shells during a pressurized period, has potential to result in catastrophic disaster, thus requiring further knowledge. This paper experimentally reveals the flame spread behaviors over fuel cylinders in high pressures. Polyethylene and polymethyl‐methacrylate cylinders with the diameter of 4.0 mm are used in this study. Ambient gas is air, and total pressures are varied from naturally normal pressure (100 kPa) to elevated pressure (500 kPa). Flame characteristics including flame appearance and flame size and burning rate and flame spread rate are investigated. Results show that in high pressure, the flame appearance is significantly affected. As the pressure increases, the blue flame disappeared, and the color of flame tip changes from luminous yellow to orange as well the orange part extends down towards the base of flame. The dimensionless flame height increases with pressure for pressure below 150 kPa and then decreases with pressure above that level. The burning rates show increasing trend with pressure and are proportional to P^0.6 and P^0.79 for polymethyl‐methacrylate and polyethylene, respectively. Besides, flame spread rates for polymethyl‐methacrylate and polyethylene both were found to be proportional to P^0.5.     

基于Abaqus的双裂纹不同间距对裂纹扩展速率的研究

扩展有限元法是近年经过大量运用的,在传统有限元的范围中求解不连续问题一种有效计算方法,它是基于单位分解的思想,在计算不连续问题时加入跳跃函数。以ABAQUS为平台,基于扩展有限元方法 (XFEM),以含双穿透型裂纹的有限宽板受横向拉伸载荷为力学模型,建立相应的裂纹尖端应力的有限元模型,研究焊接接头区域不同间距双裂纹相互作用对裂纹扩展速率的影响。结果表明:双裂纹间距的的大小并没有对裂纹的扩展速率产生影响。     

负径向电场对带电粒子俘获率影响的数值模拟

本文采用数值方法求解Grad-Shafranov方程反演EAST典型长脉冲放电实验(炮号33068)的平衡位形和磁场分布，进而结合粒子在托卡马克电磁场中的运动方程，模拟氘离子在负径向电场存在时的运动轨迹，并统计不同负径向电场下的氘离子俘获率。结果表明：随负径向电场的增大，氘离子轨迹由扩张通行轨迹向外翻香蕉轨迹再向内翻香蕉轨迹，最后向压缩通行轨迹演变；氘离子俘获率随负径向电场的增大而减小，氘离子初始速度越小，其变化越大。     

瞬态闭锁试验在0.13 μm大规模集成电路中引起的潜在损伤

瞬态剂量率辐射试验会引起集成电路发生损伤或失效，其原因至少有两种：闭锁大电流引起的电路内部金属互连熔融；累积电离总剂量引起的氧化层电荷造成阈值电压偏移。本文以一种0.13 μm体硅CMOS处理器为对象，研究了瞬态剂量率和稳态电离总剂量辐射效应规律。结果表明：瞬态剂量率闭锁效应对处理器造成了显著的潜在损伤，导致其总剂量失效阈值从1 030 Gy(Si)降低至600 Gy(Si)。研究结论对于大规模集成电路的可靠性评估和指导辐射加固设计有重要参考意义。     

硫酸体系中锰钽铌矿加压浸出研究

针对单一硫酸体系锰钽铌矿加压浸出下钽铌浸出率均不到10%的问题,在硫酸体系引入助浸剂,考察氟化铵、双氧水、反应压强、硫酸浓度、反应温度、氟化铵矿比对锰钽铌矿加压浸出的影响,采用XRD对浸渣进行物相表征。实验结果表明,在锰钽铌矿加压浸出中,引入助浸剂氟化铵,温度200℃、硫酸浓度50%及氟化铵/矿比为0.8∶1的条件下钽浸出率超过93%,铌浸出率超过96%。引入氟化铵对硫酸体系下锰钽铌矿的加压浸出效果的提升十分显著。     

Plasma gasification of the medical waste

In terms of infection control in hospitals, especially the Covid-19 pandemic that we are living in, it has revealed the necessity of proper disposal of medical waste. The increasing amount of medical waste with the pandemic is straining the capacity of incineration facilities or storage areas. Converting this waste to energy with gasification technologies instead of incineration is also important for sustainability. This study investigates the gasification characteristics of the medical waste in a novel updraft plasma gasifier with numerical simulations in the presence of the plasma reactions. Three different medical waste samples, chosen according to the carbon content and five different equivalence ratios (ER) ranging from 0.1 to 0.5 are considered in the simulations to compare the effects of different chemical compositions and waste feeding rates on hydrogen (H₂) content and syngas production. The outlet properties of a 10 kW microwave air plasma generator are used to define the plasma inlet in the numerical model and the air flow rate is held constant for all cases. Results showed that the maximum H₂ production can be obtained with ER = 0.1 for all waste samples.     

Catalytic biohydrogen production from organic waste materials: A literature review and bibliometric analysis

Global population growth and accelerated urbanisation have resulted in massive amounts of fossil fuel use and waste production. Because of its high energy content, pure nature, and fuel quality, hydrogen fuel is a viable option to fossil fuels. Biohydrogen from agricultural waste, in particular, piques concern because it generates hydrogen while still disposing of waste. This review conducted a bibliometric analysis of biohydrogen production from organic waste to trace the research trends and hotspots based on the literature in the Web of Science (WOS) database from 1970 to 2020. The present review article also focuses on highlighting various processes for converting organic waste into hydrogen, raw materials for biohydrogen production, and catalysts that could distil the latest perceptions that could shed light on a route advancing for successful catalyst design. It also seems that some intentions have been paid on studying waste materials such as pure polysaccharides, disaccharides, and monosaccharides. Among all the catalysts used, non-noble and low-cost active metals over reduced graphene oxide (rGO) support can significantly affect the activity of fermentative hydrogen production from organic waste materials. However, researches focusing on developing anaerobic membrane bioreactors for these technologies are still needed.     

FeNi@SiO2磁性纳米复合粒子的制备及磁热性能

大量制备磁热性能优异的磁性纳米粒子对磁热疗和组织复温的生物学应用具有理论价值.本研究通过高温电弧法制备FeNi磁性纳米颗粒,通过超声-沉降分级筛分得到平均粒径为80 nm的FeNi纳米颗粒,通过溶胶-凝胶法得到平均粒径为100 nm,SiO2壳层厚度为15～20 nm的FeNi@SiO2纳米复合粒子.超导量子干涉仪测定FeNi@SiO2纳米复合粒子饱和磁化强度Ms为80 emu/g.模拟磁热疗条件下,FeNi@SiO2磁性纳米粒升温速率为3.6℃/min,满足磁热疗应用要求.模拟组织复温条件下,FeNi@SiO2磁性纳米粒升温速率为61.8℃/min.磁性复合纳米粒子在不同溶剂、不同温区条件都显示了良好的热性能,可作为温度激活剂应用于磁热疗及冷冻组织的复温.本研究对磁性纳米材料的生物学应用研究具有一定的参考价值.